Living garbage disposal equipment
With the development of increasingly urbanization , the amount of garbage increased geometrically. Incineration method gradually lost the market since the dioxin and toxic produced by incineration causing irreversible effects on the environment, and for landfill, some garbage is difficult to degrade, which even takes hundreds of years, we cannot afford this even though China has a vast territory, because land is a valuable non renewable resources.
After continuous efforts, Shangqiu Jinpeng industrial Co., Ltd developed a special biomass pyrolysis equipment for domestic waste treatment. After treatment by the equipment, can get about 20% of the oil profits from domestic waste, and in the process, through the low temperature anaerobic biomass pyrolysis of domestic waste harmless treatment, to ensure environmental health.
Flow chart for living garbage disposal equipment
Living garbage disposal equipment has two system:
1. Garbage Sorting System
The equipment is applied to separate organic waste and inorganic waste from large-size refuse and processing them separately.
2. Biomass Pyrolysis Equipment
2.1 The combustible waste after sorting and shredding such as life rubber, plastics and knitted fabrics is conveyed into the low-temperature and anaerobic biomass decomposing processor. Through catalyzing and heating, oil gas is produced and then condensed into oil mixture by condenser. The remaining that can`t be liquefied is processed through gas purification system and then used to generate electricity by gas generator. The smoke after burning goes into smoke scrubbers so as to remove acid gas and dust, and then is discharged through chimney when it reaches relevant environmental standards. The residue from biomass decomposition is conveyed into carbon black collecting tanks through sealed screw, without any pollution.
2.2 The technical parameter of Biomass Pyrolysis Equipment
NO.
ITEM
Technical Parameter
1
Suitable Raw Materials
Small pieces of Waste tire, rubber, waste plastic≤5cm
2
Operating Mode
Fully Continuous Operation
3
Structure
Horizontal Type Revolve
4
Loading and discharging
Fully automatic feeding and discharging under high temperature at same time
5
Capacity(24h)
20-40Mt
6
Work Pressure
Slightly Negative Pressure
7
Oil Yield of tyres
40%-45%
8
Reactor Rotational Speed
1R/M
9
Installation Power
110kw/h
10
Cooling Method
Cycle water
11
Type of Drive
Sprocket Wheel
12
Heating Method
Direct
13
Noise dB(A)
≤85
14
Main Reactor Weight (MT)
About 20Mt
15
Total Weight(MT)
About 45Mt
16
Installation Space Required
60m*20m
17
Manpower
2/shift
18
Shipment
5*40HQ
19
Delivery time
≤70Days
Living Garbage Processing Equipment Municipal Waste Recycling,Garbage Recycling Machine,Waste To Energy Shangqiu Jinpeng Industrial Co., Ltd. , https://www.recyclings.nl
 A. Size: per drawing
B. Material: Brass etc
C. Finish: All kind
D. MOQ: 10000PCS
E. Sample lead time: 15days
Similar Products:(Per drawing)
 Machining basic parameters
1
Material
copper, aluminum, iron, stainless steel, 45 #, POM and other environmental friendly materials
2
Specifications
M1.0-M15, the maximum diameter of machining is 30MM, and the largest diameter of casting is 790MM.
3
Surface Treatment
white zinc, yellow zinc nickel, copper, chromium, tin, gold, silver, etc.
4
Tolerance
Outer diameter tolerance +/- 0.01mm;Â Â Â Length tolerance +/- 0.01mm
Threads can be checked by go-and-not-go-gauge.
5
Processing Methods
manufacture of blue drawing, sample and raw material
  Production equipment
Â
 Detection Device
Certificate
FAQ
1.Are you a manufacturer?
---Yes, we are. Warmly welcome to visit our factory at any time.
---We can according to your usage and design the hardware for you. Also can according to you drawing.
---We can give you best design and save more cost for you.
2.How does the ADL control the quality?
---During processing, the operating machine worker inspect the each sizes by themselves.
---After finished the first whole part, will show to QA for full inspection.
---Before shipment, the QA will inspect according to ISO sampling inspection standard for mass production.
---Inspection equipment: Hardness test, salt spray endurance test, mechanical sizes test, RoHS report, Â Â certificate of material and etc as per your need.
3.What's the payment term?
---100% T/T in advance normally; 50% deposit, 50% balance by T/T before shipment when order amount over 5000USD.
4.What's the delivery time?
---Normal, 7-15 working days for sample. 12-30 working days for mass production.
--If any urgent parts, we can provide preferential processing and control the delivery time as you required.
5.What is the standard of package?
---Inner is PP bag or separate Blister plastic box, keep no scratch and damage.out is carton. Then pallet. Carton size: 23*23*16, and pallet size is: 100*100*50, or as your requirement.
6.Can we get some sample?
---Sample can be provided, The clients will bear the shipping cost. The Sample cost is about 100-500 USD for each part, And it will be refund after order the mass production.
Product Name:Fatory supplier brass kunrled inserts nuts(nut-11)
 A. Size: per drawing
B. Material: Brass etc
C. Finish: All kind
D. MOQ: 10000PCS
E. Sample lead time: 15days
Similar Products:(Per drawing)
 Machining basic parameters
1
Material
copper, aluminum, iron, stainless steel, 45 #, POM and other environmental friendly materials
2
Specifications
M1.0-M15, the maximum diameter of machining is 30MM, and the largest diameter of casting is 790MM.
3
Surface Treatment
white zinc, yellow zinc nickel, copper, chromium, tin, gold, silver, etc.
4
Tolerance
Outer diameter tolerance +/- 0.01mm;Â Â Â Length tolerance +/- 0.01mm
Threads can be checked by go-and-not-go-gauge.
5
Processing Methods
manufacture of blue drawing, sample and raw material
  Production equipment
Â
 Detection Device
Certificate
FAQ
1.Are you a manufacturer?
---Yes, we are. Warmly welcome to visit our factory at any time.
---We can according to your usage and design the hardware for you. Also can according to you drawing.
---We can give you best design and save more cost for you.
2.How does the ADL control the quality?
---During processing, the operating machine worker inspect the each sizes by themselves.
---After finished the first whole part, will show to QA for full inspection.
---Before shipment, the QA will inspect according to ISO sampling inspection standard for mass production.
---Inspection equipment: Hardness test, salt spray endurance test, mechanical sizes test, RoHS report, Â Â certificate of material and etc as per your need.
3.What's the payment term?
---100% T/T in advance normally; 50% deposit, 50% balance by T/T before shipment when order amount over 5000USD.
4.What's the delivery time?
---Normal, 7-15 working days for sample. 12-30 working days for mass production.
--If any urgent parts, we can provide preferential processing and control the delivery time as you required.
5.What is the standard of package?
---Inner is PP bag or separate Blister plastic box, keep no scratch and damage.out is carton. Then pallet. Carton size: 23*23*16, and pallet size is: 100*100*50, or as your requirement.
6.Can we get some sample?
---Sample can be provided, The clients will bear the shipping cost. The Sample cost is about 100-500 USD for each part, And it will be refund after order the mass production.
Fatory Supplier Brass Kunrled Inserts Nuts
Model NO.: Nut-11
Trademark: OEM
Transport Package: According to Customer`S Requirement
Specification: M1.0-M16(Nut-11)
Origin: Guangdong, China (Mainland)
Model NO.: Nut-11
Trademark: OEM
Transport Package: According to Customer`S Requirement
Specification: M1.0-M16(Nut-11)
Origin: Guangdong, China (Mainland)
Product Name:Fatory supplier brass kunrled inserts nuts(nut-11)