Mic um 100 120 150 200 400 800 1500 3000 Mesh 150 120 100 80 40 20 10 5 Filter area(cm2) Water consumption (L) Install requirement 1.Keep space for filter install and maintenance. 2.Drainage pipe length not longer than 20m. Avoid more turns off, keep outlet pipe parallel with ground. ater filter Testing 1.Close inlet outlet valve before testing. Open by-pass valve. Wash dirties staying in pipes. 2.Open inlet valve gradually. Let water into filter till air comes out from filter house. 3.Check leak at joint part, check in/outlet pressure gauge. Connect power when comes to system pressure. 4.Set up drainage time based on system pressure data. 5.Open outlet valve gradually if testing is normal. Close by-pass valve back to normal filtering. 6.Observe several differential pressure changes and drainage. Finish testing if normal. 1st operation notice Follow below steps in 1st operation: Check drainage pipe connection. No up-inclined angle. Check connection tighten or not. Check control box in a dry environment. Connect power cord, green light means normal. Make sure electrical parts is dry. Water is forbidden into control box. Mic um 100 120 150 200 400 800 1500 3000 Mesh 150 120 100 80 40 20 10 5 Filter area(cm2) Water consumption (L) Install requirement 1.Keep space for filter install and maintenance. 2.Drainage pipe length not longer than 20m. Avoid more turns off, keep outlet pipe parallel with ground. ater filter Testing 1.Close inlet outlet valve before testing. Open by-pass valve. Wash dirties staying in pipes. 2.Open inlet valve gradually. Let water into filter till air comes out from filter house. 3.Check leak at joint part, check in/outlet pressure gauge. Connect power when comes to system pressure. 4.Set up drainage time based on system pressure data. 5.Open outlet valve gradually if testing is normal. Close by-pass valve back to normal filtering. 6.Observe several differential pressure changes and drainage. Finish testing if normal. 1st operation notice Follow below steps in 1st operation: Check drainage pipe connection. No up-inclined angle. Check connection tighten or not. Check control box in a dry environment. Connect power cord, green light means normal. Make sure electrical parts is dry. Water is forbidden into control box. Driving in a cold vehicle is never fun. But on a chilly day it takes some time for your Alloy Seat Heated,Alloy Wire Seat Heated,Alloy Wire Car Seat Heated,Car Seat Heated Cover Seat Heating JiLin Province Debang Auto Electric Co.,Ltd. , https://www.carseatheating.com
How It Works
 The unit consists of two stages of filtration, a coarse pre-filter and a stainless steel fine screen.
 The unwanted solids accumulate on the inner surface of the fine screen, building up a filter cake, which filters out even finer particles, creating a pressure differential. Once the pressure drop reaches a preset level, a rinse cycle is activated by the factory supplied control system.
 The solids are removed from the fine screen using a spot backwashing method, which aggressively sucks the dirt off the screen, similar to a vacuum cleaner, and are carried to the drain via the rinse valve. The dirt collector rotates, ensuring the entire screen is cleaned each cycle. The process takes a matter of seconds, without interruption of system flow.
Control method
Filter has differential switch and integrator. Once the pressure drop reaches a preset level, a rinse cycle is activated by the PLC controller.
Feature
structure compact
low water consumption
fine filter degree
low pressure drop
ApplicationÂ
1.Chilling water treating: such like cooling tower, water supplement system, air conditioning system, heat exchange system.Â
2.Raw water treating: such like surface water, lake, sea water, tank water, well to remove grind, sand, algae, organism etc.
3.Cycling industry water: cooling tower, polishing process water, ion exchange water, spraying process water, heat exchange plant, rolling plant, casting plant etc.
4.Irrigation: farm, dip field, golf, lawn etc.Â
5.Recycle water
Filter degreeÂ
Horizontal type
Â
Model
Pipe
T/H
Filter area(cm2)
Drain(mm)
Water consumption(L)
Motor(Kw)
Weight(KG)
XLQ-50XM
50
20
1500
50
75
0.55
85
XLQ-80XM
80
50
1500
50
75
0.55
87
XLQ-100XM
100
80
3000
50
150
0.55
210
XLQ-125XM
125
100
3000
50
150
0.55
212
XLQ-150XM
150
150
7000
50
150
0.55
220
XLQ-200XM
200
300
7000
50
150
0.55
220
XLQ-250XM
250
450
11000
80
400
0.55
395
XLQ-300XM
300
600
11000
80
400
0.55
405
XLQ-350XM
350
900
13500
80
400
0.55
625
Â
Install way
HorizontalÂ
Unit capacity
15-900T/H,Achieve parallel install to achieve big capacity
Min work pressure
0.25Mpa
Max work pressure
1.0Mpa,1.6Mpa
Micron
80-500um
Control way
Differential pressure, time and manual
Max temperature
65ºC (reach to 100ºC if required)
Back wash time
50-90S
Rotating speed
14-20rpm
Clean way
Scanning type
Differential pressure in cleaning
0.01-0.08Mpa
Back wash water consumption
Approximate 280-310kg
Voltage
AC220V 380V,50Hz,3PH,CONTROLLER:Â 220V
Motor power
0.37Kw
Material
Carbon steel with anti-corrosion painting
Screen
Multi stainless steel mesh + pvc structure
Drain valve
Cast ion with antir-corrosion paintingÂ
PLCÂ controller
Pressure drop VS flow rate
Vertical type
Â
ModelÂ
PipeÂ
T/H
Drain(mm)
motor(KW)
weight(KG)
XLQ-200XT
200
300
7500
50
250
0.55
340
XLQ-250XT
250
450
11000
80
400
0.55
350
XLQ-300XT
300
650
11000
80
400
0.55
365
XLQ-350XT
350
900
13800
80
400
0.55
630
XLQ-400XT
400
1200
13800
80
400
0.55
650
XLQ-350XT
350
1500
13800
80
400
0.55
690
Â
Install way
Vertical installation
Unit capacity
15-900T/H, Achieve parallel install to achieve big capacity
Min work pressure
0.25Mpa
Max work pressure
1.0Mpa,1.6Mpa
Micron
20-500um
Control way
Differential pressure, time and manual
Max temperature
65ºC (reach to 100ºC if required)
Back wash time
60-120S
Rotating speed
14-20rpm
Clean way
Scanning type
Differential pressure in cleaning
0.01-0.08Mpa
Back wash water consumption
Approximate 500kg
Voltage
AC220VÂ Â 380V,50Hz,3PH,Controller:Â 220V
Motor power
0.37Kw
Material
Carbon steel with anti-corrosion painting
Screen
316SS (Woven, ,multi-layer sintered, wedge)
Drain valve
cast ion with antir-corrosion paintingÂ
PLCÂ controller
Pressure drop VS flow rate
Install noticeÂ
1.One check valve must be installed at filter outlet. Return pressure and back water is forbidden, in case of screen out of shape.
2.If system wok pressure over 0.8MPa, should install break valve at drain pipe to reduce impact to screen.
3.Notice motor rotating direction. Shut off power immediately once back rotating (anti-clock wise ) occurs. )
4.Installation each part according to arrow direction.Â
5.Sudden pressure relief at outlet pipe is forbidden. Take normal work pressure 1.3MPa for example, if suddenly open branch valve at outlet, it will occur instant huge different pressure, which damage screen.
6.Make sure filter used under correct work pressure, capacity.Â
7.If alarms, open by-pass valve for temporary back washing solutions.Â
8.Make sure control box have constant power supply. If power off, users can open by-pass valve, close in and outlet valve and control box switch.
Installation view
The video of working principle:Â https://www.youtube.com/watch?v=61YAxgeWdro
Â
Â
Equipment can through into operation directly, as already has trial testing. Users can adjust settings based on actual use. Change relay's program and parameter is forbidden.
Internal fitting
Â
How It Works
 The unit consists of two stages of filtration, a coarse pre-filter and a stainless steel fine screen.
 The unwanted solids accumulate on the inner surface of the fine screen, building up a filter cake, which filters out even finer particles, creating a pressure differential. Once the pressure drop reaches a preset level, a rinse cycle is activated by the factory supplied control system.
 The solids are removed from the fine screen using a spot backwashing method, which aggressively sucks the dirt off the screen, similar to a vacuum cleaner, and are carried to the drain via the rinse valve. The dirt collector rotates, ensuring the entire screen is cleaned each cycle. The process takes a matter of seconds, without interruption of system flow.
Control method
Filter has differential switch and integrator. Once the pressure drop reaches a preset level, a rinse cycle is activated by the PLC controller.
Feature
structure compact
low water consumption
fine filter degree
low pressure drop
ApplicationÂ
1.Chilling water treating: such like cooling tower, water supplement system, air conditioning system, heat exchange system.Â
2.Raw water treating: such like surface water, lake, sea water, tank water, well to remove grind, sand, algae, organism etc.
3.Cycling industry water: cooling tower, polishing process water, ion exchange water, spraying process water, heat exchange plant, rolling plant, casting plant etc.
4.Irrigation: farm, dip field, golf, lawn etc.Â
5.Recycle water
Filter degreeÂ
Horizontal type
Â
Model
Pipe
T/H
Filter area(cm2)
Drain(mm)
Water consumption(L)
Motor(Kw)
Weight(KG)
XLQ-50XM
50
20
1500
50
75
0.55
85
XLQ-80XM
80
50
1500
50
75
0.55
87
XLQ-100XM
100
80
3000
50
150
0.55
210
XLQ-125XM
125
100
3000
50
150
0.55
212
XLQ-150XM
150
150
7000
50
150
0.55
220
XLQ-200XM
200
300
7000
50
150
0.55
220
XLQ-250XM
250
450
11000
80
400
0.55
395
XLQ-300XM
300
600
11000
80
400
0.55
405
XLQ-350XM
350
900
13500
80
400
0.55
625
Â
Install way
HorizontalÂ
Unit capacity
15-900T/H,Achieve parallel install to achieve big capacity
Min work pressure
0.25Mpa
Max work pressure
1.0Mpa,1.6Mpa
Micron
80-500um
Control way
Differential pressure, time and manual
Max temperature
65ºC (reach to 100ºC if required)
Back wash time
50-90S
Rotating speed
14-20rpm
Clean way
Scanning type
Differential pressure in cleaning
0.01-0.08Mpa
Back wash water consumption
Approximate 280-310kg
Voltage
AC220V 380V,50Hz,3PH,CONTROLLER:Â 220V
Motor power
0.37Kw
Material
Carbon steel with anti-corrosion painting
Screen
Multi stainless steel mesh + pvc structure
Drain valve
Cast ion with antir-corrosion paintingÂ
PLCÂ controller
Pressure drop VS flow rate
Vertical type
Â
ModelÂ
PipeÂ
T/H
Drain(mm)
motor(KW)
weight(KG)
XLQ-200XT
200
300
7500
50
250
0.55
340
XLQ-250XT
250
450
11000
80
400
0.55
350
XLQ-300XT
300
650
11000
80
400
0.55
365
XLQ-350XT
350
900
13800
80
400
0.55
630
XLQ-400XT
400
1200
13800
80
400
0.55
650
XLQ-350XT
350
1500
13800
80
400
0.55
690
Â
Install way
Vertical installation
Unit capacity
15-900T/H, Achieve parallel install to achieve big capacity
Min work pressure
0.25Mpa
Max work pressure
1.0Mpa,1.6Mpa
Micron
20-500um
Control way
Differential pressure, time and manual
Max temperature
65ºC (reach to 100ºC if required)
Back wash time
60-120S
Rotating speed
14-20rpm
Clean way
Scanning type
Differential pressure in cleaning
0.01-0.08Mpa
Back wash water consumption
Approximate 500kg
Voltage
AC220VÂ Â 380V,50Hz,3PH,Controller:Â 220V
Motor power
0.37Kw
Material
Carbon steel with anti-corrosion painting
Screen
316SS (Woven, ,multi-layer sintered, wedge)
Drain valve
cast ion with antir-corrosion paintingÂ
PLCÂ controller
Pressure drop VS flow rate
Install noticeÂ
1.One check valve must be installed at filter outlet. Return pressure and back water is forbidden, in case of screen out of shape.
2.If system wok pressure over 0.8MPa, should install break valve at drain pipe to reduce impact to screen.
3.Notice motor rotating direction. Shut off power immediately once back rotating (anti-clock wise ) occurs. )
4.Installation each part according to arrow direction.Â
5.Sudden pressure relief at outlet pipe is forbidden. Take normal work pressure 1.3MPa for example, if suddenly open branch valve at outlet, it will occur instant huge different pressure, which damage screen.
6.Make sure filter used under correct work pressure, capacity.Â
7.If alarms, open by-pass valve for temporary back washing solutions.Â
8.Make sure control box have constant power supply. If power off, users can open by-pass valve, close in and outlet valve and control box switch.
Installation view
The video of working principle:Â https://www.youtube.com/watch?v=61YAxgeWdro
Â
Â
Equipment can through into operation directly, as already has trial testing. Users can adjust settings based on actual use. Change relay's program and parameter is forbidden.
Internal fitting
Â
engine heater to kick in, which means you have to live with the frigid conditions until the
engine has a chance to warm up. Seat heaters are electronic heating elements that install
into your seat giving your body warmth on even the coldest days.
Automatic Self -Cleaning Agricultural Irrigation Water Filtration System Water Filter
Model NO.: XLQ
Backwash Time: 50-90s
Screen: Multi Stainless Steel Mesh + PVC Structure
Voltage: AC220V 380V,50Hz,3pH,Controller:220V
Trademark: Peide
Transport Package: Wooden Cases
Specification: Carbon Steel, 304ss or 316L
Origin: China
Model NO.: XLQ
Backwash Time: 50-90s
Screen: Multi Stainless Steel Mesh + PVC Structure
Voltage: AC220V 380V,50Hz,3pH,Controller:220V
Trademark: Peide
Transport Package: Wooden Cases
Specification: Carbon Steel, 304ss or 316L
Origin: China
Automatic Self -Cleaning Agricultural Irrigation Water Filtration System Water Filter
Automatic Self -Cleaning Agricultural Irrigation Water Filtration System Water Filter